Latest publications
Latest publication announcements
-
2026-10-14
-
ISO 4437-2:2024
WithdrawnPlastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 2: Pipes
Withdrawn on 14/10/2026
-
-
2026-10-09
-
Power transformers, Part 22.6: Power transformer and reactor fittings – Electric fans for transformers
Standard objective is to outline the service conditions and the mechanical and electrical requirements of electric fans used in the cooling circuits of power transformers and re...
-
Systems and software engineering — Life cycle management — Part 8: Technical reviews and audits on defence programs
This document establishes the requirements for technical reviews and audits to be performed throughout the acquisition life cycle for the US Department of Defense (DoD) and othe...
-
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 4.10: Particular requirements for pole-mounted pruners
Closing date for comments 04/12/2026
-
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery - Safety - Part 4.11: Particular requirements for edgers
Closing date for comments 04/12/2026
-
-
2026-10-07
-
ISO 11298-1:2018
WithdrawnPlastics piping systems for renovation of underground water supply networks — Part 1: General
Withdrawn on 07/10/2026
-
-
2026-09-25
-
Explosive atmospheres - Part 38: Equipment and components in explosive atmospheres in underground mines
This document is published as a dual logo standard and is applicable for the explosion protection requirements for the construction, testing and marking for Group I Ex Equipment...
-
-
2026-09-18
-
Quality management systems – Requirements
Standard objective is to specify requirements for a quality management system when an organization —
(a) needs to demonstrate its ability to consistently provide products and se... Supersedes by 9001.
-
-
2026-09-16
-
Quality management systems — Requirements
This document specifies requirements for a quality management system when an organization:
needs to demonstrate its ability to consistently provide products and services that m... Supersedes by 9001. -
Plastics piping systems for water supply and drainage and sewerage under pressure — Modified poly(vinyl chloride)(PVC-M) pipe
This document specifies requirements for pipe and integral joints of higher level of impact resistant PVC-M for the conveyance of water and waste water under pressure. The pipes...
-
-
2026-09-15
-
Structures for mine shafts — Part 5: Shaft system structures
This document specifies the loads, the load combinations and the design procedures for the design of shaft system structures in both vertical and decline shafts. The shaft syste... Supersedes by 19426.
-
Structures for mine shafts — Part 4: Conveyances
This document specifies the loads, the load combinations and the design procedures for the design of the steel and aluminium alloy structural members of conveyances used for the... Supersedes by 19426.
-
Structures for mine shafts — Part 1: Vocabulary
This document specifies the terms and definitions related to the structures for mine shafts, used throughout ISO 19426 series.
Terms used in mining can vary from conventional en... Supersedes by 19426. -
Cellular plastics — Self-supporting metal faced sandwich panels
This document specifies requirements for factory made, self-supporting, double skin metal‑faced insulating sandwich panels where the insulating core materials are intended to be...
-
Structures for mine shafts — Part 3: Sinking stages
This document specifies the design loads and the design procedures for the structural design of stages and components of stages.
The loads specified in this document are not app... Supersedes by 19426. -
Structures for mine shafts — Part 2: Headframe structures
This document specifies the design loads and the design procedures for the structural design of headframe structures of mine shafts and their components for permanent and sinkin... Supersedes by 19426.
-
Refrigerated food lockers — Thermal and energy performance, ratings, environmental test conditions and associated testing methods
This document specifies requirements for the thermal and energy performance of refrigerated food lockers in given environmental conditions and intended for the temporary cold st...
-
Statistical methods in process management — Capability and performance — Part 7: Capability of measurement processes
This document defines a procedure to validate measuring systems and a measurement process in order to state whether a given measurement process can satisfy the requirements for ... Supersedes by 22514.
-
Steel and iron — Determination of chromium content — Indirect titration method
This document specifies a potentiometric titration method for the determination of chromium content in steel and iron.
The method is applicable to chromium contents between 1 % ... Supersedes by 15355. -
Oilseeds — Simultaneous determination of oil and water contents — Method using pulsed nuclear magnetic resonance spectrometry
This document specifies a rapid method for the determination of the oil and water contents in oilseeds using pulsed nuclear magnetic resonance (NMR).
It is applicable to rapesee... Supersedes by 10565. -
Risk-based product quality data interchange in e-commerce
This document provides information on how to address product quality data interchange based on risk assessment for consumer product safety in e-commerce. This document:
analyse...
-
-
2026-09-11
-
Test method for burning velocity measurement of A2L flammable gases
This document specifies a method of measuring the burning velocity (BV) of lower burning refrigerants (</= 10 cm/s) for use with other standards that utilize the BV for deter...
-
Information technology — JPEG systems — Part 10: Reference software
This document specifies a reference software implementation of ISO/IEC 19566-5 [1]. The reference software is accompanied with a reference dataset which provides an extensive li...
-
Climate change management — Carbon neutrality
This document specifies principles, requirements and guidance for achieving and demonstrating carbon neutrality through the quantification, reduction and offsetting of the carbo...
-
Hydraulic fluid power — Procedures used to certify the standard reference material SRM 2806d used in ISO 11171
This document describes the criteria and procedures used by the United States National Institute of Standards and Technology (NIST) to certify the calibration material SRM 2806d...
-
Ultrasonic testing of hardmetals
This document specifies an A-type ultrasonic pulse contact method applying the ultrasonic longitudinal wave technique to hardmetals.
This document is applicable to the ultrasoni...
-
-
2026-09-10
-
Fine ceramics (advanced ceramics, advanced technical ceramics) — Measurement of viscosity of ceramic slurry by use of a rotational viscometer
This document specifies a method for measurement of the viscosity of a ceramic slurry using a rotational viscometer. The method only involves rotations with a monotonic angle va... Supersedes by 19613.
-
Small craft — Hull construction and scantlings — Part 9: Sailing craft appendages
This document defines the loads and specifies the scantlings of sailing craft appendages on monohull sailing craft with a length of hull (LH) measured in accordance with ISO 866... Supersedes by 12215.
-
-
2026-09-09
-
Information technology for learning, education and training — Metadata for learning resources — Part 2: Dublin Core properties
This document provides a set of properties for the description of learning resources from ISO 15836-1 and ISO 15836-2 using the framework provided in ISO/IEC 19788-1. This docum...
-
Oil and gas industries including lower carbon energy — Workover rigs for offshore fixed platforms
This document gives requirements for the design, fabrication, installation, commissioning and integrity management of workover rigs on offshore fixed platforms.
This document is... -
Automation systems and integration — Equipment behaviour catalogues for virtual production system — Part 4: Application methods
This document specifies requirements, a framework, a general specification procedure, a guide for elaboration, and categorization of application methods of an equipment behaviou...
-
Oil and gas industries including lower carbon energy — Enhanced oil recovery terms and definitions — Part 1: General vocabulary
This document defines fundamental definitions for enhanced oil recovery (EOR) concepts and core methodologies, specifically addressing thermal recovery, gas flooding, chemical f...
-
Indoor air — Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air — Active sampling method
This document specifies a sampling method to determine the quantity of formaldehyde (HCHO) in the air with the range of approximately 1 µg/m3 to 1 mg/m3 in a time-weighted avera... Supersedes by 16000.
-
Traditional Chinese medicine — Chuzhen instruments
This document specifies the general requirements and test methods of Chuzhen instruments.
It is only applicable to non-disposable Chuzhen instruments.
It is not applicable for a... -
ISO 12215-9:2012
WithdrawnSmall craft — Hull construction and scantlings — Part 9: Sailing craft appendages
Withdrawn on 09/09/2026
-